Jonsered GC 2125 Uživatelský manuál

GT 2125 GC 2125 GC 2125C Oper ator’s manual Please read the oper ator’s manual carefully and make sure you understand the instructions before using

10 – EnglishGENERAL SAFETY PRECAUTIONSSharpening grass cutters and grass blades• See the cutting attachment packaging for correct sharpening instructi

English – 11ASSEMBLYFitting the loop handle(GT 2125)• Position the handle on the shaft. Note that the handle must be mounted below the arrow on the sh

12 – EnglishASSEMBLYDismantling:• Undo the knob (at least three turns).• Push the knob towards the coupling.• Carefully twist the lower half of the sh

English – 13ASSEMBLYFitting the blade guard/combination guard, grass blade and grass cutter(GC 2125, GC 2125C)• Hook the blade guard/combination guard

14 – EnglishFUEL HANDLINGFuel safetyNever start the machine:1 If you have spilt fuel on it. Wipe off the spillage and allow remaining fuel to evaporat

English – 15FUEL HANDLINGMixing• Always mix the gasoline and oil in a clean container intended for fuel.• Always start by filling half the amount of th

16 – EnglishSTARTING AND STOPPINGCheck before starting• Never start the machine indoors. Exhaust fumes can be dangerous if inhaled.• Observe your surr

English – 17STARTING AND STOPPINGStartingPrimer bulb: Press the primer bulb repeatedly until fuel begins to fill the bulb. The bulb need not be complet

18 – EnglishWORKING TECHNIQUESGeneral working instructionsBasic safety rules1 Look around you:• To ensure that people, animals or other things cannot

English – 19WORKING TECHNIQUES• Work systematically to and fro across the area, clearing a width of around 4-5 m on each pass. This exploits the full

2 – English KEY T O SYMBOLS Symbols WARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in s

20 – EnglishWORKING TECHNIQUESCutting• The trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower. Keep the cord paral

English – 21MAINTENANCECarburetorYour Jonsered product has been designed and manufactured to specifications that reduce harmful exhaust fumes. The engi

22 – EnglishMAINTENANCEFine adjustment of the idle speed TAdjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. Fir

English – 23MAINTENANCECooling systemTo keep the working temperature as low as possible the machine is equipped with a cooling system.The cooling syst

24 – EnglishMAINTENANCETwo-piece shaft (GC 2125C)The drive shaft end in the lower shaft should be lubricated with grease every 30 hours. There is a ri

English – 25MAINTENANCEMaintenance scheduleThe following is a list of the maintenance that must be performed on the machine. Most of the items are des

26 – EnglishTECHNICAL DATATechnical dataNote 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure lev

English – 27TECHNICAL DATAApproved accessories Type Cutting attachment guard, Art. no.GT 2125Blade shaft thread 3/8 RTrimmer head Tap-N-Go VII (R) 530

28 – EnglishFEDERAL EMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS AND OBLIGATIONSThe EPA (The US Environmental Protection Agency), Environme

"Clic"12356796,0 m18'483,05 m9'2,0-2,4 mm.079-.095"10 cm 4"6"15 cmTap-N-Go 25

English – 3 CONTENTS Contents Note the f ollowing before starting: Please read the oper ator’s manual carefully.Long-term exposure to noise can res

1Trimmy H II234567897,5 m 25'2,0-2,4 mm.080-.095"12 15 cm 6"~ 3,7 m 12' 15 cm 6"

"Clic"12356710118,5 m28'484,2 m14'2,4-2,7 mm.095-.106"10 cm 4"6"15 cmS35

12432,4-2,7 mm.095-.106"4,25 m14'4,25 m14'B6"15 cmA6"15 cmS355

Tap-N-Go 35"Clic"12356798,5 m28'484,3 m14'2,4-2,7 mm.095-.106"10 cm 4"6"15 cm

´®z*x°G¶5p¨´®z*x°G¶5p¨1Auto 3223456789104,0 m 13'2,4 mm.095"~2,0 m6,5'6"6"15 cm15 cm

´®z*x°G¶5p¨2005-03-15´®z*x°G¶5p¨1088953-95

4 – English INTR ODUCTION Dear customer! Cong ratulations on your choice to buy a Jonsered product!Your purchase gives you access to professional h

English – 5 WHA T IS WHA T? What is what?3130GC2125C 1 Trimmer head2 Grease filler cap, bevel gear3 Bevel gear4 Cutting attachment guard5 Shaft6 Lo

6 – English GENERAL SAFETY PRECA UTIONS Impor tantPersonal protective equipment HEARING PR OTECTIONWear hearing protection that provides adequate n

English – 7 GENERAL SAFETY PRECA UTIONS Mac hine ′′′′ s safety equipment This section descr ibes the machine ′ s safety equipment, its purpose, an

8 – English GENERAL SAFETY PRECA UTIONS Vibration damping system Y our machine is equipped with a vibration damping system that is designed to redu

English – 9GENERAL SAFETY PRECAUTIONSLocking nutA locking nut is used to secure some types of cutting attachment.When fitting, tighten the nut in the o