Jonsered CS 2188 Uživatelský manuál

English CS 2188 Operator ′′′′ s manual Please read the oper ator’s manual carefully and make sure you understand the instructions before using the m

GENERAL SAFETY PRECAUTIONS10 – Englishchain saw, including the cutting equipment, is insulated from the handles by vibration damping units.Cutting har

GENERAL SAFETY PRECAUTIONSEnglish – 11gauge clearance. Too large a clearance increases the risk of kickback.• Keep the chain properly tensioned! If t

GENERAL SAFETY PRECAUTIONS12 – English• Drive link width (mm/inches)• Number of drive links.Sharpening your chain and adjusting depth gauge settingGen

GENERAL SAFETY PRECAUTIONSEnglish – 13• Always file cutting teeth from the inside face. Reduce the pressure on the return stroke. File all the teeth on

GENERAL SAFETY PRECAUTIONS14 – English• Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination

GENERAL SAFETY PRECAUTIONSEnglish – 15• Check that the groove in the edge of the bar is clean. Clean if necessary.• Check that the bar tip sprocket tu

GENERAL SAFETY PRECAUTIONS16 – English• Whether the tip of the bar is uneven or badly worn. If a hollow forms on the underside of the bar tip this is

ASSEMBLYEnglish – 17Fitting the bar and chainCheck that the chain brake is in disengaged position by moving the front hand guard towards the front han

FUEL HANDLING18 – EnglishFuelNote! The machine is equipped with a two-stroke engine and must always been run using a mixture of petrol and two-stroke

FUEL HANDLINGEnglish – 19• In temperatures below 0°C (32°F) some oils become too viscous. This can overload the oil pump and result in damage to the o

KEY T O SYMBOLS 2 – English Symbols on the mac hine: W ARNING! Chain saws can be dangerous! Careless or incorrect use can result in serious or fat

STARTING AND STOPPING20 – EnglishStarting and stoppingCold engineStarting: The chain brake must be engaged when the chain saw is started. Activate the

STARTING AND STOPPINGEnglish – 21starts, quickly apply full throttle; the throttle start lock will automatically disengage.As the chain brake is still

WORKING TECHNIQUES22 – EnglishBefore use:1 Check that the chain brake works correctly and is not damaged.2 Check that the rear right hand guard is not

WORKING TECHNIQUESEnglish – 23lose control. Both situations can cause serious personal injury.6 Before moving your chain saw switch off the engine and

WORKING TECHNIQUES24 – Englishladder, in a tree or where you do not have firm ground to stand on.6 Always use a fast cutting speed, i.e. full throttle.

WORKING TECHNIQUESEnglish – 255 Do the conditions and surrounding terrain affect how safely you can stand and move about?Two factors decide whether th

WORKING TECHNIQUES26 – EnglishTree felling techniqueSafe distanceThe safe distance between a tree that is to be felled and anyone else working nearby

WORKING TECHNIQUESEnglish – 27FellingFelling is done using three cuts. First you make the directional cuts, which consist of the top cut and the botto

WORKING TECHNIQUES28 – Englishfind out which lengths of bar are recommended for your saw.There are methods for felling trees with a diameter larger tha

WORKING TECHNIQUESEnglish – 29How to avoid kickbackWhat is kickback?The word kickback is used to describe the sudden reaction that causes the chain sa

CONTENTS English – 3 Contents KEY TO SYMBOLS Symbols on the machine: ... 2Symbols in the operator’s manual: .

MAINTENANCE30 – EnglishCarburettor adjustmentThe carburettor can be designed in different ways, depending on existing environmental and emissions legi

MAINTENANCEEnglish – 31Rec. idle speed: 2700 rpmFine adjustmentWhen the machine has been ”run-in” the carburettor should be finely adjusted. The fine ad

MAINTENANCE32 – EnglishFunction, Basic settings, Fine adjustmentFunction• The carburettor governs the engine’s speed via the throttle control. Air and

MAINTENANCEEnglish – 33High speed jet H• The high speed jet H influences the power and engine speed of the machine. If the high speed jet is set too ri

MAINTENANCE34 – EnglishChecking the inertia brake releasePlace the chain saw, with the engine switched off, on a stump or other stable surface. Releas

MAINTENANCEEnglish – 35Chain catcherCheck that the chain catcher is not damaged and is firmly attached to the body of the chain saw.Right hand guardChe

MAINTENANCE36 – Englishuse a muffler if the spark arrestor mesh is missing or defective.The muffler is designed to reduce the noise level and to direct

MAINTENANCEEnglish – 37Remember that the recoil spring is coiled under tension in the starter housing.• Remove the recoil spring from inside the pulle

MAINTENANCE38 – EnglishLubricating the bar tip sprocketLubricate the bar tip sprocket each time you refuel. Use the special grease gun and a good qual

MAINTENANCEEnglish – 39• Too low engine temperature.• Icing of the air filter and carburettor.Special measures are therefore often required:• Partly ma

4 – English INTR ODUCTION Dear Customer , Cong ratulations on your choice to buy a Jonsered product!We are convinced that you will appreciate with

40 – EnglishMAINTENANCEMaintenance scheduleThe following is a list of the maintenance that must be performed on the machine. Most of the items are des

English – 41TECHNICAL DATATechnical dataNote 1: Noise emissions in the environment measured as sound power (LWA) in conformity with EC directive 2000/

42 – EnglishTECHNICAL DATABar and chain combinationsThe following cutting attachments are approved for the model Jonsered CS 2188.Saw chain filing and

English – 43TECHNICAL DATAEC-declaration of conformity(Applies to Europe only)Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel +46-36-146500, declares u

1153188-26´®z+U2r¶6>¨´®z+U2r¶6>¨2010-07-13Original instructions

English – 5 WHA T IS WHA T? What is what on the c hain saw?Jonsered CS 2188Jonsered ABHuskvarna, SWEDEN2978279101164512312227212019182824171615142

GENERAL SAFETY PRECA UTIONS 6 – English Bef ore using a new chain saw • Please read this manual carefully.• Check that the cutting equipment is cor

GENERAL SAFETY PRECA UTIONS English – 7 possib le. Your dealer, forestry school or your library can provide information about which training mater

GENERAL SAFETY PRECAUTIONS8 – English• The chain brake (A) can either be activated manually (by your left hand) or automatically by the inertia relea

GENERAL SAFETY PRECAUTIONSEnglish – 9of the front hand guard, the chain brake can only be activated by the inertia action. Will my hand always activa